Overall, this cube turned great when I got it out the package. It was very smooth, a little bit loose, and the corner cutting was great. The one problem was that my sticker wasn't fully placed on so when I turned it with my ring finger, one of the stickers wen't through my finger nails and cut me but it wasn't that bad. Next, its quite slow, although its smooth, the cube feels slow in my opinion. But for $10, you can go wrong with this cube. I would recommend buying it!

Out of the box the YueXiao Pro is really controllable and fast. I have a Valk Power M and a Gan354 M but the YueXiao Pro is a lot better and my new Main! It comes in a nice box and with great half-bright-scheme. Cornercutting is great too. Although it has no Squared off Corners, the Corner Twists are low.
I love this cube!

I have this cube since 2 months and it's the best I've ever had . There is juste a problem : the stickers ... They start to left after 1 month :/

This cube is a speed cube! But its best to put magnets in it to improve its speed. If you wanna good cube, GET THIS CUBE BECAUSE ITS GOOD!!!!!!!!

This cube is a speed cube! But it’s best to put magnets in it to improve it’s speed. If you wanna good cube, GET THIS CUBE BECAUSE IT’S GOOD!!!!!!!!

So, I was looking for a new 3x3 main, and I decided to buy this cube to try it out.
It's already overlubed OOTB, It was very scratchy, slow, locky, and a bit greasy on the outside.
But after i wipe off the lubes, tension it (1 - 2 turns to the left) with the tool included, lubed it with Silk and then it got so fast, smooth and I just got a new ao5 and single PB with it :D. Now it is my main.

Ill break this review into two parts: before setup and after set up.
Before- the colorless shades were very bright. I was surprised and didnt like them at first, it was my first Stickerless, but after a while the shades grew on me. It was sort of oily and really loose. Turning was great though, super buttery feel.
After setup- the only thing I did Was tighten the tensions, no lube at all. Iv put a couple hundred solves on it and I love it. Its just as good as any high end cube that would cost $35-50. Corner cutting is great, almost line to line(45 degrees). No pops, no locks, the inner design is great. All in all, awesome cube.

this is a nice cube. The corner cutting of this cube is amazing. It can cut over 45 degrees and can reverse corner cut about half of a piece. This is one of the fastest cubes i own. I would definitely recommend this 3x3 to you.

I’ll break this review into two parts: before setup and after set up.
Before- the colorless shades were very bright. I was surprised and didn’t like them at first, it was my first Stickerless, but after a while the shades grew on me. It was sort of oily and really loose. Turning was great though, super buttery feel.
After setup- the only thing I did Was tighten the tensions, no lube at all. Iv put a couple hundred solves on it and I love it. It’s just as good as any “high end” cube that would cost $35-50. Corner cutting is great, almost line to line(45 degrees). No pops, no locks, the inner design is great. All in all, awesome cube.

Out of the box this cube was overlubed, papery, and sluggish all at the same time. It was a indescribable hot mess that truly disappointed me. After breaking it in with about 50 solves (which were well above my average) it was still bad. I put some weight 1 and 2 on the pieces and weight four on the core and it got a little better. It smoothened out and was at least usable but was still super slow and had this non likable gummy, clacky feeling. A few weeks later I washed all of the lube out of the pieces and just put in dnm37 and while the feeling got better it is still way to slow. I have tried some at competitions that were amazing but I just cannot seem to get mine to setup good. Overall this cube is bad and the best part of it was the mini screwdriver that came with it which I use a lot.